• +965 51122049
Hantek DPO6104B Digital Storage Oscilloscope 4 Channels 100MHz 1 GSa/s Sample Rate Waveform Generator Spectrum Analyzer

Hantek DPO6104B Digital Storage Oscilloscope 4 Channels 100MHz 1 GSa/s Sample Rate Waveform Generator Spectrum Analyzer

KWD225.000KWD225.000
0%Off

Hantek DPO6104B Digital Storage Oscilloscope 4 Channels 100MHz 1 GSa/s Sample Rate Waveform Generator Spectrum Analyzer


1 product available

 

 


Share:
The Hantek DPO6004B(C) series oscilloscope is a diverse 4 channel oscilloscope. With its sampling rate of 1GSa/s and a bandwidth from 80 to 200 MHz, you will be able to accurately perform measurements. The oscilloscopes have 64Mpts memory capabilities and a 400 000 wfm/s waveform capture rate.
four input channels: CH1 CH2 CH3 CH4
input channels bandwidth: 100MHz
real-time sampling: 1GSa / s
memory record length: 64Mpts = 64,000 points
vertical resolution of A / D converter: 8bit
voltage sensitivity from 500μV / div to 10V / div
waveform capture rate: up to 400,000 wfm / s
oscilloscope display:
▶️ large 7-inch
display ▶️ displayed resolution: 800x480
▶️ TFT touch screen with 16M colors and 24 bit
▶️ supports 256-step light intensity scale
 for mono-color waveforms ~ analogous to phosphor as in analog oscilloscopes
DVM - built-in 5 digit digital multimeter
Digital Volt Meter
built-in 6-digit frequency meter
mathematical operations
FFT spectral analysis
extensive trigger system
over 14 trigger types:
Edge, Pulse Width, Video, Slope, Overtime, Window, Pattern, Interval, Under Amp, UART, LIN, CAN, SPI, IIC I2C
possibility of triggering by digital signals - serial buses
cursor measurements
automatic measurements: measurement of 32 parameters
saving and reading waveforms to * .csv files
Pass / Fail function
Auto Scale function - the so-called AUTO function - self-setting - setting the oscilloscope parameters
built-in communication interfaces:
▶️ USB Host - communication with a computer
▶️ USB Device - memory stick support
▶️ LAN
Windows PC software
support for SCPI remote control commands
decoding of serial buses: RS232, UART, I2C, SPI, LIN, CANset contains:
DPO6104B digital oscilloscope
certificate of factory calibration of the oscilloscope
oscilloscope probe with x1 / x10 divider - 4 pcs.
USB connection cable
power cord  uk plug
Oscilloscope function
AcquisitionReal-time sample rate1 GSa/s(single channel) 500 MSa/s(two channels)
250 MSa/s(three/four channels);
Note:digital channel 12,34 open at the same time,it is considered as one channel
Peak detectionAnalog channel 4ns
Note:digital channels don’t support
Average modeAnalog channel

All channels reach N time samples at the same time,N can be selected from

2、4、8、16、32、 64、128、256、512 and 1024.

Note:digital channels don’t support
High resolutionUp to 12bit
Note:digital channels don’t support
Minimum test pulse width8ns
Memory depthSingle channel 64M
Two channels 32M
Three,four channels 16M
InputChannel quantity4 analog channels
Note:data channels can’t be opened
3 analog channels
Note:digital channel LA1/LA2/LA3/LA4/LA1LA2/LA3LA4
2 analog channels
Note:digital channels infinitize
1 analog channel
Note:digital channels infinitize
0 analog channel
Note:digital channels infinitize
Input couplingDC、AC or GND
Note:digital channels don’t support
Input impedance,DC couplingAnalog channel
25pF±3 pF,1MΩ±2%
Digital channel
(300KΩ±2%) ,(8 pF±3 pF)
Supported probe attenuation  factorAnalog channel 1X、10X、100X、1000X
Voltage classes300V CAT II
Maximum input voltageAnalog channel 300VRMS (10X)
Digital channel -25V~25V
HorizontalWaveform interpolation(sin x)/x
Maximum record lengthSingle channel maximum 64M
Two channels maximum32M
three/four channels maximum 16M
Horizontal scale rangeDSO6084 DSO6104
2ns/div~100s/div  1, 2, 5 step by step
Time base modeY-T、X-Y、Roll
X-Y numberChannel 1,2 1 XY channel、channel3 4 1 XY channel
Zero offset±0.5 div× minimum time base gear
Sample Rate and±25ppm
Delay Time Accuracy
Clock drifting≤±5 ppm/year
Delta Time Measurementsingle,“acquisition”mode
Accuracy
(Full Bandwidth)±(1 sample interval+100ppm×reading+0.6ns)
>16 times averages
±(1 sample interval+100ppm×reading+0.4ns)
Sample interval=sec/div÷200
VerticalBandwidth(-3db)DPO6084DPO6104DPO6204
80MHz100MHz200MHz
Vertical resolutionAnalog channel 8bit
Digital channel 1bit
Vertical scale rangenput BNC position is 500μV/div~10V/div
Position range500μV/div to 120mV/div,±1V
122mV/div to 1.2V/div,±10V
1.22V/div to 10V/div,±50V
Optional analog bandwidth limitationTypical 20MHz
Bass response(-3db)In BNC position is≤10Hz
Rising time in BNC position,typicalDPO6084DPO6104DPO6204
≤4.4ns≤3.5ns≤1.8ns
Vertical gain accuracy

In “normal” or “average” acquisition mode,the accuracy o

f 10V/div to 10mV/div is ±3%

In “normal” or “average” acquisition mode,the accuracy of

5mV/div to 500uV/div is ±4%.

DC offset accuracy±0.1 div±2 mV±1% offset value
The isolation of channelsDC maximum bandwidth:>40 dB
Note: Bandwidth reduced to 6MHz when using a 1X probe
TriggerTrigger level range±5 divisions from the center of the screen
Trigger modeauto、general、single
LevelCH1~CH4±4 divisions from the center of the screen
Holdoff range8ns~10s
Trigger level accuracyCH1~CH4

0.2 div×volts/div within ±4 divisions

from the center of the screen

Edge triggerSlopeRising edge,falling edge,rising or falling edge
Signal sourceCH1~CH4,
D1.0~D1.3,
D2.0~D2.3,
D3.0~D3.3,
D4.0~D4.3
Pulse width triggerPolarityPositive polarity,negative polarity
Condition(When)<,>, !=, =
Signal sourceCH1~CH4,
D1.0~D1.3,
D2.0~D2.3,
D3.0~D3.3,
D4.0~D4.3
Pulse width range8ns ~ 10s
Video triggerSignal standardNTSC, PAL
Signal sourceCH1~CH4
SynchronizationScanning line、line number、odd field、even field、all field
Slope triggerSloperise,fal
condition(When)<,>, !=, =
Signal sourceCH1 ~ CH4
Time range8ns ~ 10s
Overtime triggerSignal sourceCH1~CH4,
D1.0~D1.3,
D2.0~D2.3,
D3.0~D3.3,
D4.0~D4.3
PolarityPositive polarity,negative polarity
Time range8ns ~ 10s
Window triggerSignal sourceCH1~CH4LA1~LA4
Pattern triggerPattern0:low level;1:high level;X:ignore;
Level(signal source)CH1~CH4
Interval triggerSloperise,fall
condition(When)<,>, !=, =
Signal sourceCH1~CH4,
D1.0~D1.3,
D2.0~D2.3,
D3.0~D3.3,
D4.0~D4.3
Time rangeTime range8ns ~ 10s
Delay triggerEdge typeRising edge,falling edge
Signal sourceCH1~CH4
condition(When)<,>, !=, =
Time range8ns ~ 10s
Set up hold triggerEdge typeRising edge,falling edge
Signal sourceCH1~CH4
condition(When)<,>, !=, =
Time range8ns ~ 10s
Runt triggerPolarityPositive polarity,negative polarity
Condition(When)<,>, !=, =
Signal sourceCH1~CH4
Time range8ns ~ 10s
UART triggercondition(When)start、stop、data、odd-even check、reception error
Signal source(RX/TX)CH1~CH4,
D1.0~D1.3,
D2.0~D2.3,
D3.0~D3.3,
D4.0~D4.3
Data formatHex(hexadecimal)
Data length1 byte
Data bit width5 bit, 6 bit, 7 bit, 8 bit
Odd-even checknone、odd、even
Free levelhigh、low
Baud rate (optional)

110/300/600/1200/2400/4800/9600/14400/19200/38400/57600

/115200/230400/380400/460400 bit/s

Baud rate(user-defined)300bit/s~334000bit/s
LIN triggercondition(When)

Interval field、synchronization field、ID field、synchronization error

、identifier、IDand data

Signal sourceCH1~CH4,
D1.0~D1.3,
D2.0~D2.3,
D3.0~D3.3,
D4.0~D4.3
Data formatHex(hexadecimal)
Baud rate(optional)

110/300/600/1200/2400/4800/9600/14400/19200/38400/57600

/115200/230400/380400/460400 bit/s

Baud rate(user-defined)300bit/s~334000bit/s
CAN triggercondition(When)Start bit、remote frame ID、data frame ID、frame ID、remote frame data、data frame data、wrong frame、all errors、answer error、overload frame
Signal sourceCH1~CH4
Data formatHex(hexadecimal)
Baud rate(optional)10000, 20000, 33300, 500000, 62500, 83300, 100000, 125000, 250000, 500000, 800000, 1000000
Baud rate(user-defined)5kbit/s~1Mbit/s
SPI triggerSignal sourceCH1~CH4,
D1.0~D1.3,
D2.0~D2.3,
D3.0~D3.3,
D4.0~D4.3
Data formatHex(hexadecimal)
Data bit width4, 8, 16, 24, 32
IIC triggerSignal source (SDA/SCL)CH1~CH4,
D1.0~D1.3,
D2.0~D2.3,
D3.0~D3.3,
D4.0~D4.3
Data formatHex(hexadecimal)
Data index0~7
opportunity(condition)Start bit、stop bit、no response、address、data、restart
MeasurementcursorVoltage difference between cursors △V
Time difference between cursors △T
Reciprocal of △T,in Hertz(1/△T)
Auto measurementfrequency、period、mean、peak-to-peak、RMS、minimum、mixmum、rising time、falling time、+ width、- width、base、top、middle、amplitude、overshoot、preshoot、rising edge phase difference、falling edge phase difference、+ duty、- duty、period mean、PRMS、FOVshoot、ROVshoot、BWIDTH、FRF、FFR、LRR、LRF、LFR、LFF
DVMData sourceCH1,CH2,CH3,CH4
Measurement typeDC effective value
AC effective value
DC
Frequency meterhardware 6 bits frequency meter
Arbitrary waveform generator
Arbitrary waveform generator(for oscilloscopes with signal source channels)Channel number2/3channels
Sample rate200MSa/s
Vertical resolution12 bits
Maximum frequency25 MHz
Standard waveformssin、square、pulse、triangular,noise、DC
Sinc、index、semi-distortion、lorentz,dual tone multiple frequency,gauss,ECG
Arbitrary waveformArb1,Arb2,Arb3,Arb4
SinFrequency range0.1Hz~25MHz
square/pulseFrequency range0.1Hz~10MHz
triangular waveFrequency range0.1Hz~1MHz
Sampling waveFrequency range0.1Hz~1MHz
IndexFrequency range0.1Hz~5MHz
Semi-distortionFrequency range0.1Hz~1MHz
lorentzFrequency range0.1Hz~1MHz
Dual tone multiple frequencyFrequency range0.1Hz~1MHz
GaussFrequency range0.1Hz~1MHz
ECGFrequency range0.1Hz~1MHz
Arbitrary waveFrequency range0.1 Hz to 10 MHz
Waveform length8KSa
Frequencyaccuracy100 ppm(<10 kHz) 50 ppm(>10 kHz)
resolution0.1 Hz or 4 bits,take the greater one
AmplitudeOutput range10mV~7Vp-p(high impedance)
5mV~3.5Vp-p(50Ω)
DC offsetrange±3.5 V,high impedance
±1.75 V,50 Ω
resolution100 μV or 3 bits,take the greater one
accuracy2%(1 kHz)
Output impedance50 Ω
Logic analyzer
Logic analyzerInput impedance,DC couplingDigital channel
(300KΩ±2%) ,(8 pF±3 pF)
Threshold value4 channels in 1 group adjustable threshold value
Threshold optionTTL(1.4 V)
5.0 V CMOS(+2.5 V)
3.3 V CMOS(+1.65 V)
2.5 V CMOS(+1.25 V)
1.8 V CMOS(+0.9 V)
ECL(-1.3 V)
PECL(+3.7 V)
LVDS(+1.2 V)
0V
User-defined
Threshold range±7.0V,10mV step by step
Threshold accuracy±(100mV+3% threshold setting)
Dynamic range±5.0V+ threshold
Minimum voltage swing500 mVpp
Vertical resolution1 bit
General specifications
DisplayDisplay type7″TFT  diagonal liquid crystal
Display resolution800(horizontal)*480(vertical)pixels
Display colour16 million colours(24 bits true colour)
Persistence timeminimum、1 s、5 s、10 s、30S、infinite
Display typedot、vector
Display modeColor temperature,gray scale
Display brightnessadjustable
Grid typeadjustable
Grid brightnessadjustable
InterfaceStandard interfaceUSB Host,USB Device,LAN, EDU signal WIFI
Aux(trigger output/PassFail )–only EDU with this interface
Optional interfacePassFail
UART
HDMI
General specificationsProbe compensator output
Output voltage ,typicalabout 2Vpp input≥1MΩ load
frequency、typical1kHz
Power supply100-120VACRMS(±10%),45Hz to 440Hz,CATⅡ
120-240VACRMS(±10%),45Hz to 66Hz,CATⅡ
Power consumption<30W
FuseT,3.15A,250V,5x20mm
Operating temperature0~50 °C (32~122 °F)
Storage temperature-40~+71 °C (-40~159.8 °F)
Humidity≤+104℉(≤+40°C): ≤90% relative humidity
106℉~122℉ (+41°C ~50°C): ≤60% relative humidity
Cooling methodconvection
AltitudeOperating and nonoperating3,000m(10,000 feet)
Mechanical shockRandom vibration0.31 g RMS from 50Hz to 500Hz,
10 minutes on each axis
Nonoperating2.46g RMS from 5Hz to 500Hz,
10 minutes on each axis
Operating50g,11ms,half-sine wave
MechanicalSize318 x 140 x 150mm(length x width x height)
Weight2900g

 


Add your review

Your email address will not be published. Required fields are marked *

Please login to write review!

Upload photos

Looks like there are no reviews yet.

Related Products